sewing machine - upper thread keeps breaking

Discussion in 'Arts and Crafts' started by Grumpy's Gal, Apr 16, 2006.

  1. Grumpy's Gal

    Grumpy's Gal DIS Veteran

    Oct 5, 2004
    anyone have any suggestions? I have a singer sewing machine, I have read the book that came with it, and it's breaking every 20 inches or so. I am so frustrated right now..... :confused3
  2. KAMommy

    KAMommy <font color=teal>I am ADDICTED to America's Next T

    Sep 23, 2002
    I would try checking the tension setting on the machine. If it has gotten shifted, that can cause the thread to break.

    I know my DS "helped" me one day and turned the tension setting up very high. Took me forever to figure out why I couldn't sew. :rotfl:
  3. Avatar


    to hide this advert.
  4. carol1231

    carol1231 DVC Member '98: BWV, VWL, BCV

    Jan 14, 2005
    Definetly check what your tension setting is. But also.... are you using good thread? I was working on a craft project and bought some cheap thread, it kept breaking as you described. I change the tension back and forth, didn't help. Then finally I changed thread, and it was as good as new.

    Good luck!!
  5. dyna

    dyna DIS Veteran

    Jun 30, 2005
    make sure the bobbin is inserted correctly too that can do it along with tension to tight or cheap thread.
  6. denisem

    denisem DIS Veteran

    Sep 19, 2001
    If all the above suggestions don't work, you might try taking the whole bobbin mechanism out and clean/oil the machine. Your book usually has instructions, and it's surprising how much lint & junk gets stuck in there.
  7. Marianne0310

    Marianne0310 Mouseketeer

    Jul 8, 2001

    If you're still having a problem with the thread breaking, and you've adjusted the tension, changed the thread, and cleaned the bobbin area there might be a couple of other things to try.

    Change the needle to a needle that is compatible with the fabric you're sewing on, and also thread the bobbin with the same thread that the machine is threaded with.
  8. FabricGal

    FabricGal Earning My Ears

    May 25, 2006
    If you are sure the thread and the bobbin are threaded right and have put in a new needle, is the thread locking correctly? If the upper thread is breaking, it means something is wrong with the bobbin thread. I had this problem.
    It may be that the hooking device is not working correctly. I have an old singer model 6610. I had to take it to an old singer repairman, and he replaced the part that the bobbin goes into and now it sews just fine.

    I hope this helps you.
  9. SallyfromDE

    SallyfromDE DIS Veteran

    Apr 15, 2007
    I know this is an old thread, but I had to jump in. Look at the spool of thread it'self. On one end of the spool is a cut, where the thread gets locked so it won't unwind. When you put it on the machine, make sure it is not where the thread can get hooked while your sewing. If the spool stand is horizontal, and the thread gets threaded from there to the left, make sure that little cut is to the right hand side. So as it unwinds, it won't get hungup and break. I hope this hasn't confused anyone.
  10. design_mom

    design_mom probably more like my dad than I care to admit

    Feb 1, 2007
    I know this thread is old, but I just had a similar problem with my machine (a 1967 singer) and couldn't figure it out. I tried adjusting the tension but that didn't seem to be doing anything. I took it to the repair shop and they said that the pin the controls the tension was worn out (so adjusting it really *wasn't* doing anything!!) The pin is only about $5. Of course the labor to install it... :rolleyes1

Share This Page