Marty and Mike Wazowski - Costumes: Part 1
Alright, time is counting down to getting these costumes finished. We potentially have a local Halloween fundraiser with G's theater group at the beginning of October. So realistically we have about 1.5 months to finish everything up. Let's not leave it to the last minute as there's still plenty to do. At this point, we have four occasions planned for the costumes: Halloween fundraiser, WDW Halloween Party, Halloween, and Disneyland 5k. So we're getting our money's worth. Which is good because... $$$.
Anyways, let's recap what's happened thus far. As a reminder, I'll write this as more of a "this is what happened" than a "here is the exact step-by-step you should follow with no errors", because in my mind seeing what went wrong is just as important as what went right.
As a reminder, this is what we were aiming for:
-Fully body colored suit.
-Fabric costume that goes past waist line
-Googly eye
-3-D mouth
-Sock on back
-Must be transportable via airplane
So, to start we found our fully body suits without anything covering the head. The goal was to get as close to Marty (orange) and Mike (green) as we could using the body suits, and then color match the remainder of the costumes to them. We ended up getting:
(
link)
(
link)
In person, the green is more limey and the orange is more bright orange, but we felt the colors were good enough.
We're somewhat following the instructions from the Simplicity 7415 (
link)
Specifically going for "View 2" but without the hoods or neck piece.
We then took a trip to JoAnn Fabrics to pick up some supplies.
-6.5 yards Kona Tangerine Cotton Fabric for Marty (
link)
-7.0 yards Symphony Kelly Green Polyester Blend Fabric for Mike (
link)
-Coats and Clark Dual Duty XP General Purpose Thread - x2 Emerald Green, x2 Orange, x1 White, and x1 Black (
link)
-Dritz 1/2 inch 4 yard non-roll - white (link)
-Dritz 1/2 inch 4.5 yard braided - white (
link)
-Wrights Double Fold Quilt Binding 1/2 inch x 3 yard - x3 Kiwi and x3 Orange (
link)
-Premium Felt 72 inch wide - 1 yard Black and 1 yard White (
link)
-1.5 yard twisted cord - Grass Green and Antique
-9x12 Gold Felt
-Fairfield Ultraweight Bonded 100% Polyester Batting (
link)
It took a bit of searching, but we felt like the two fabrics we got were close in color to the body suits.
The first step was laying out the pattern. For G, we are making the size medium (which is for a 4-5 foot person) and for me the size large (for 5-6 foot person). We started with the Marty costume first because it was smaller and thus if we needed to make changes then we would waste less material.
Here's some of how the instructions are laid out:
I won't show the whole instructions because that isn't fair to the company. But from the instructions you can see it told us how much material to buy, and of what, for each size and such. It then lays out based on which view (we're #2) you'll be doing what in terms of cutting out material. In addition to the instructions, you have the pattern:
For our use, we're only really going for the wedge pattern and the collars. Otherwise, we aren't really using the other patterns available in this kit.
We cut out the size medium wedge and then we laid out the orange fabric in a doubled over layer. This way, when we cut out one pattern it will make it in duplicate. Per the instructions, for a 44 inch wide piece of fabric we were able to lay three patterns side by side. It was important to note which side of the fabric was the selvages and then the pattern told us which way to lay. This apparently has to do with the stretch of the fabric.
We went through and pinned the pattern to the fabric, and then we cut it out.
We used fabric scissors for the cutting which are specifically made for this task.
The instructions call for 6 wedges to make the costume, but we diverged here. We wanted the costume to look really full. So there's a lot of debate as to how to make that happen. Additionally, G has a thing about weird fabrics touching her. So we knew that we needed a layer of something in between G's body suit and the batting. So we decided to double up on the wedges, each have a 1 inch batting, and then sandwich them together. Instead of 6 wedges, we would then need 12 wedges. After cutting out 12 fabric wedges, we cut out 12 batting wedges. The batting didn't have as much rigidity as I was hoping for. I toyed with the idea of using an egg foam mattress instead based on this
youtube video (
link), but I was voted down since we already had the batting to try out first.
We used regular scissors to cut out the batting. We traced the pattern with a black marker, but this turned out to be a bad idea because the marker didn't really dry all to much and thus it was getting all over our hands and some of the orange fabric. We lesson learned there.
Next Post -
Marty and Mike Wazowski - Costumes: Part 2